Видео

Yes I’ll make one for 500 lb barrels. Have been looking for a long time for an idea that I like. I’m very fussy and your design works for me😊

HEY ROSS, ARE YOU STILL ARROUNMD ?

Hi Ross, i would like to have the drawing. To which email should i sent my question?

thank you Sir for sharing great work. I think i will use your plan other than the expensive poorly made kits available. I would very much like to have your drawings/plans. How do i go about getting them? Thank you!! I would leave my Email but the spammers have ruined that. Can you contact me or an email for you?

2 pulleys is not serpentine

Quicker way to make the special screw. Lock Tight nut to a partially threaded 10-32 screw then cut nut to countersink angle. Then cut the un-threaded end of the screw off and point it.

USA

Good.

Make that cutter 6 inches bigger, and it will be better. Nice build though

Iv got everything to build my stump grinder..I found a motorcycle front rotor.10/78 round x 1/4 thick..I'm going to try that..the rotor is steel, not cast..I have a hydro that I will use to move the machine..I found a vertical, horizontal gear box..to run hydro

New Zealand 🇳🇿

The grinder wheel should be 6 " larger then the pully.

Auckland Chan Brothers

Disk or plate cam spindexr video

Cow I’m An Animal

New Zealand Let’s Visit

Thank you for this. Very helpful for the hydraulic press forming that I want to do. Nice work!

Made in CHINA. Take the plastic hose back to Harbor Freight and tell them you want a new hose. Right the date some where when you brought this and send your warranty card in, and save the sales slip in the owners book. I don't even think they make or sell these today. You can split wood be both directions. 11/2021

Pretty good for a first attempt... But the cutters are spaced and leave material between cuts.. Need to make some 40° angled cutters and flip every other one..

Your comment section has rejected at least 10 of my requests for the pulleys drawings over the past month. Please just post them on your comments or add a picture to your video or add bullet points in the comments for pitch, diameters, etc. Thanks

Can you post the belt part # and the pitch dia. of the pulleys? I did not see an OD for the pulleys from Franco video. Is it possible to get the pulleys, belt, and 3D printed cover?

You gave very good detailed instructions, great video!👍

Howdy Russ! I'd be very grateful for a set of your plans. Email me at planeflyer21@yahoo.com please. Thanks!

Thank you fixed ours the same way u did works great now !!!!!!!!! Thank you ...

U can buy o rings at harbor freight

Thank you for your video. Very informative and funny. "Fat old men dont dont like bending over". LOL

Another consideration I failed to mention in the video, this design allows the device to be bumped away from the part when it is accidently run into with rapid travel, so it doesn't get broken. It is just a matter of time till that occurs.

Very nice unpacking and assembly video you made sir. I like the modifications you made and I believe I shall follow our lead.

Well-made video of a fine shop-made tool. I truly enjoy and appreciate your attention to detail. Your humble words do not accurately represent your knowledge and skills. It was great hearing you mention, "giving back." Thank you for sharing.

I'd love your plans. Psdkevin@gmail.com I love your ideas.

would love to get your plans for this upgrade. cd*edwards@sasktel.net and replace the * with a . will reach me. thanks.

about 35 years ado a friend bought a 22 ton Duerr from Grainger for about $1600. When he didn't need it anymore i bought it for $800 and used it for 10 years. this week i received a 34 ton yardmax that cost $1499. it is a tough versatile machine. My how things have changed.

Thanks for sharing the knowledge, I have a similar project brewing!

Thank you for sharing, love your adjustable die

marine grease. motor needs some marine greezee

I just found this video. Well done.

So now that you have been using it, what’s your opinion of it? Thanks Oh, I just noticed the guard, no need to send a picture.

Can you send a pic of the motor guard you made? Thanks

Well I wish you lived nearby me I have you do lot project for me and you've done a good job on that looks damn good

I just thought of something on that motor before you put that motor back on that plate Get a mudflap quarter inch thick and I'll say that it helped the vibration overtime

Predator engines work really good 👍💪👈

I really like it! Well done sir!

Do you know what the HP and GPM of the motor and pump?

You Did A Wonderful Job Fabricating This Jib Crane To Your Liking Kind Sir, Great Job!!! Thanks For Posting.

Ross I agree with Freakingstang . You have one of the best stoves made on earth. I used to sell the Avalon which was the sister stove to the Lopi. Travis Industries is one of the best. Over all the years we had only one call back on a wood stove and it was because they were not shutting the blower off when they cleaned it? Their complaint was it was too dirty!! By not turning off the blower they were sucking soot out ?? Maybe try splitting some of your wood a little smaller this will help it dry faster . Good luck Ross ! Great little invention!

Oh and do not run that blade back and forth till it binds up until it stops you're not good for a hydraulic system we have a couple of inches right before it stops you don't want to bottom that blade out so it stops on his own you know what I'm saying okay thank you

You're doing really good with that video until you burn your hand anyway to make sure you run an additive in your gasoline if you're using ethanol gas please that's a nice piece of equipment you got you've done a lot of add-ons let's not mess it up remember a fuel additive seafoam is a good one

On the same way I did it with a XRS home gym I didn't use any the directions I just put it together maybe they can look right to me and it works perfect. It had a problem with it that's just the way guys like I saw her if I can push it together and push it together what Direction's that's what I say

There are two types of countries, those that use the metric system, and one that put a man on the moon!

Awesome information, thanks for sharing!